Leaks
First and foremost – tile is not waterproof. Grout is not waterproof. Adding sealer to your tile or stone will not make it waterproof. Your shower should be completely waterproof before a box of tile is even opened! No matter which waterproofing method you choose, proper substrate preparation is the only thing that will make your shower waterproof.
If you have a leak in your shower – stop using it immediately if at all possible. If that is not possible (it’s your only shower) have the shower repaired – immediately. If you see water leaking it is likely not nearly as much water as you don’t see leaking into your wall cavity and structural framing. By the time you ‘see’ most leaks the framing is normally already considerably compromised.
No, there is nothing you can put over your tile to make your shower waterproof if you have a leak – not even sealer. A tile or stone sealer is made to make your tile and grout stain-resistant, not waterproof. It does this by sealing the pores of the tile and stone to slow (NOT STOP) the absorption of liquid and prevent staining. It only means you have more time to clean up the spilled red wine cherry kool-aid before it stains anything.
Substrates
Drywall is not an acceptable substrate for your shower. Use a waterproofing membrane – that’s it. Cement backerboards are the standard and there are also other products such as waterproofed, gypsum based boards like Denshield and waterproofed, foam-based sheets like wedi or kerdi board.
Cement backerboards are not waterproof. They are water stable, which simply means that they will not swell or disintegrate when exposed to moisture or water – they won’t change size. But they are just like your driveway, they will soak in water, hold water, and dry out, just like your driveway when it rains. If using backerboards there needs to be a waterproof membrane utilized as well.
Membranes
If you are using a topical waterproofing membrane such as a liquid like hydroban, or a sheet like kerdi, do not use a moisture or vapor barrier behind your substrate. If you have a vapor or moisture barrier behind your substrate do not use a topical membrane on the front of it. This combination creates two waterproof barriers with your substrate sandwiched between them. any vapor or moisture trapped between them has absolutely no way to dissipate. This is lovingly referred to as a ‘mold sandwich’. It is not tasty. Use either a moisture or vapor barrier behind your substrate or a topical membrane on the face of it. One or the other – never both.
If you are using a topical membrane and you have an exterior wall with either plastic facing or kraft paper facing you need to cut slits into that facing before installing your substrate. If you do not it will create the aforementioned mold sandwich. Give moisture or vapor somewhere to dissipate.
Shower-tub transitions
There should be a gap between your tub or acrylic shower base and the bottom of your backerboard. If you are using a traditional barrier waterproofing method you do not need to do anything with this gap. Do not fill it with silicone! This will trap moisture running down your barrier and it will have nowhere to go. If you are using a topical method you can fill it with silicone if you want. If you are using liquid you should fill it with silicone. This creates a waterproof plane between your membrane and the tub or base so water or moisture ends up in the drain rather than in your wall.
When you tile you can tile right over that gap. You should not fill this gap with thinset behind the tile – it will crack due to movement. Your wall and tub or base will expand and contract at different rates – it will crack any cement-based product you place between the two. This includes thinset as well as grout. You do not need a solid backing behind your tile over this gap – it should be less than 1″ wide. You shouldn’t normally be walking on that tile in that particular spot. Yes, it can just hang there.
Grout
If your grout is cracking it is due to movement 99.9% of the time. Type ‘cracking’ into the search box up there and you’ll find in-depth explanations.
If you have white, or lighter than normal grout when you’re finished grouting it may be efflorescence. This is mainly due to minerals in the water being left on the surface of the grout when the water evaporates. It is usually indicative of either incorrectly mixed grout or using too much water while cleaning the grout – not wringing out your sponge enough. This is normally only on the surface of your grout. Scratch the very top layer of your grout in an inconspicuous spot with your fingernail. If you have the correct, or at least a darker, color beneath the surface that is the likely cause. The easiest, quickest fix, provided it is only the very top layer, is to get some drywall sanding sponges and go over the grout lines very lightly. Just like burnt toast – scrape it to the color you like.
Give us a call @ 905-892-5756 and we will provide a free estimate.
No comments:
Post a Comment